Squat Squad, this one is a look back to May 26, 2021, just days after Taurus dropped the GX4 and made a splash in the micro-compact carry market. Once people started getting their hands on one, the most common question in my comments was simple: how does this thing come apart? So instead of another review, I put the GX4 on the bench and walked through field stripping, cleaning, lubricating and reassembling it, plus taking the magazine apart. This is a bench how-to, not a range test.
Disclosure: the GX4 in this video was provided by Taurus for testing and evaluation. Taurus did not see the video before it was published.
TL;DR
- Tools: a flathead screwdriver (or a pocket knife at the range), your usual cleaning rod and patches or a 9mm bore snake, and a pin punch if you want to go deeper into the striker or the magazines.
- The key trick: the takedown pin on the right side of the frame looks like a flathead screw. A quarter turn counterclockwise lets the slide come forward and off.
- You do pull the trigger during takedown, so verify the gun is unloaded first. Every time.
- Lube the friction points with a few drops, not a flood: top of the chamber, the lug and guide rod area, the slide rails and the frame rails.
- Don’t skip the mags: a good share of malfunctions come from dirty magazines.
- Relationship: pistol provided by Taurus for testing and evaluation.
Why a field strip video for a brand-new gun?
When I made this, the GX4 had only been out for a few days, and it had already been reliable and a pleasure to shoot for me. A lot of you had either bought one or were looking at one, and the manual is fine, but it’s always easier to watch someone do it. If you want my full thoughts on the pistol itself, read my Taurus GX4 micro-compact CCW value review. This article sticks to maintenance.
What you’ll need
- A flathead screwdriver, or a pocket knife if you’re at the range
- Your regular cleaning supplies: cleaning rod, patches and solvent, or a 9mm bore snake instead of the rod
- A pin punch (or something like it) if you plan to pull the striker or take the magazines apart
- A quality gun oil. I’ve been using Lucas Oil Extreme Duty Gun Oil for about a year now
Step 1: Unload and clear
Like a lot of striker guns today, the GX4 needs you to pull the trigger during takedown. So the first step is non-negotiable: drop the magazine, rack the slide, and visually confirm the chamber is empty. Once you’ve verified the gun is unloaded, release the slide and pull the trigger.
Heads up: the order I show is slightly different from the manual. I find it works better this way, but the manual is always the official reference.
Step 2: The quarter-turn takedown pin
This is the part that throws people. On the right side of the frame there’s a pin that looks like a flathead screw. With the gun ready for takedown, the slot in that pin sits vertical. Put your screwdriver or the tip of a pocket knife in the slot and turn it a quarter turn counterclockwise.
As you turn it, you’ll see and feel the slide move forward. At that point, simply slide it off the front of the frame.
Step 3: Guide rod and barrel
Push in on the back of the guide rod to take the spring pressure off, then lift it out of the slide. Then pull the barrel. For basic maintenance, that’s as far as you need to go: frame, slide, guide rod assembly and barrel.
Optional: pulling the striker
If you suspect the striker or its channel needs cleaning, grab a thin punch. Push down on the sleeve at the back of the slide to relieve the pressure, pull it off, and then pull the striker out. Keep pressure on the back while you do it, otherwise it can fly right back out at you.
Step 4: Clean and inspect
Use your favorite solvent to get the residue off everything. While it’s apart, this is also a great time to inspect each part for any cracks or wear where there shouldn’t be any.
Step 5: Lube the high-friction spots
Do you absolutely need oil? No, guns will function without it. But running dry will surely induce more malfunctions and increase wear. Sometimes a good lube is just a very good idea. Here’s where it goes on the GX4:
- Barrel: a bit on top of the chamber, where it locks up with the slide, plus on the lug and where the guide rod sits.
- Slide: inside the slide rails, which ride over the frame, and at the striker release.
- Frame: the frame rails that contact the slide.
Don’t go crazy. A few drops of quality lubricant is enough. Too much oil can actually attract and hold more dust and grime, which causes its own problems later.
Step 6: Reassembly and function check
- Put the barrel back in the slide.
- Put the guide rod back in.
- If you pulled the striker, put it back in now, keep pressure on it, and make sure it clicks into place.
- Set the assembled slide onto the frame.
- Rack the slide all the way to the rear, slowly let it go forward, then pull the trigger to function test.
- Check the takedown pin and make sure it’s back in the vertical position.
The manual says to lock the slide back and turn the pin back a quarter turn by hand. What I found is that when you rack the slide back and let it go forward, the slide locks into place and the pin rotates to vertical by itself. Either way, confirm it’s vertical. Then cycle the gun a few more times and dry fire to make sure all is well.
Don’t forget the magazines
Most gun owners never clean their magazines, but a good amount of malfunctions are actually caused by them. Carbon from the gun finds its way into the mag while it’s seated, and if you ever drop one on the ground, soil, sand or rocks can get inside and make the spring or follower bind. That’s why a lot of match shooters clean their mags every time they hit the dirt.
To take a GX4 magazine apart:
- Hold the magazine in one hand with your thumb over the base plate.
- With a pin punch, press down on the tab, then slowly slide the base plate off.
- Keep the spring’s retainer plate held down and let it out slowly. If you just let go, it’ll come flying out and could hurt you or someone nearby.
- You’ll end up with the body, the base plate, the follower and spring, and the retainer.
No lube in the magazine. Just clean it: start with the inside of the body using patches and solvent or a magazine brush, then wipe down the follower, the spring and the retainer plate.
To reassemble, drop the spring and follower back into the body, press it down with your thumb (again, don’t let go), slide the base plate back on, and make sure it clicks into place.
More Taurus on SlavGuns
- Taurus GX4: Best Micro-Compact CCW Value?
- Taurus G3C detailed review
- Taurus G3C TORO optics-ready carry
- Taurus TX22 review
- Taurus TX9 in Flat Dark Earth
Gear and more
- The pistol: Taurus GX4 9mm (1-GX4M931) at KYGUNCO
- The lube I use: Lucas Oil Extreme Duty Gun Oil at MidwayUSA
- Eye pro, ear pro, lead wipes and everything else I run: SlavGuns Amazon storefront
- Members get extra perks: join the Squat Squad on YouTube
How often do you actually clean your carry gun, and do you ever clean your mags? Tell me in the comments. Thanks for reading, and keep squatting!
Some links are affiliates.





Comments